Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
This post which follows in relation to A Step-by-Step Guide to Installing a Bathtub is incredibly entertaining. Read it for your own benefit and figure out what you think about it.
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is also a reasonably difficult project. If the old tub is easily easily accessible, the task can relocate easily; if you have to open a wall to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about using one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This short article will help you mount a brand-new bath tub in your shower room if you have currently gotten a new tub and do not require to alter the plan of your previous supply of water pipes.
Your tools and also product checklist ought to consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather troublesome due to the limited access that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the tap and the sink. Protect the faucet in place with the supplier provided backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the bath tub in the called for placement. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and check all joints and new pipework for leakages and also tighten them if essential. Load the bath tub and also examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub must wait up until the bathtub has been made use of at the very least when as this will resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining structure supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to split an inflexible seal, causing the water to permeate the wall in between the bathroom and the tiling, resulting in issues with wetness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not think about this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece of content was worthwhile. Make sure you take a moment to share this article if you enjoyed reading it. Bless you for your time. Please check our blog back soon.
Pricing Report this page